Image is for your reference only,please check specifications for details

LPC1519JBD64E - NXP
Manufacturer:
NXP
ManyChip's Part#:
MC7364703
Category:
Microcontroller, MCU IC
Package:
LQFP-64
Datasheet:
Datasheet 3D Model
Description:
NXP LPC1519JBD64E 32Bit Microcontroller, ARM Cortex-M3, 72MHz, 256KB, 36KB, 64Pins, LQFP
Stock Locations:
Availability:
297 pcs In Stock
MOQ:
1 pcs
Unit Price:
$ 3.65

Updated at 02/11/2025 10:30:15(UTC+8)

Certifications

ManyChip is committed to product quality and safety with ISO 9001, ISO 13485, ISO 45001, UL, RoHS, CQC and REACH certifications.

Description

Overview
The LPC1500 microcontroller series are optimized for fast, easy, and high-precision motor control and incorporate all the features required for high-accuracy sensored and sensorless motor control, enabling simultaneous control of two motors in highly flexible configurations. Based on the ARM® Cortex™-M3 processor, the LPC1500 microcontroller series has two 12-bit, 12-channel, 2 Msps ADCs and an on-chip quadrature encoder interface (QEI) to enable highly accurate control of both sensored and sensorless motor combinations. Four on-chip comparators enable fast-response over-current/voltage monitoring and protection; and four flexible SCTimer/PWM timers provide up to 28 PWM channels in a tightly coupled analog and timing subsystem, with minimal load on the CPU. Ideal for use with a wide range of brushless DC (BLDC) motors, permanent-magnet synchronous motors (PMSM), and AC induction motors (ACIM) commonly found in products such as large home appliances, HVAC, industrial pumps and generators, and more. They are also well suited for industrial applications requiring high-precision data sampling and real-time control, such as digital power and instrumentation. The LPC1500 series of microcontrollers are fully supported by the LPC software ecosystem and an extensive collection of tools, drivers and middleware.
With ultra-efficient motor control firmware, easy-to-use GUI-based tuning tools, and two new motor control solution kits, NXP LPC1500 microcontrollers simplify evaluation and development of motor control applications, without requiring deep motor control experience.
MoreLess
## Features
* System:
* ARM Cortex-M3 processor, running at frequencies of up to 72 MHz.
* ARM Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).
* System tick timer.
* Serial Wire Debug (SWD) with four breakpoints and two watchpoints.
* Single-cycle multiplier supported.
* Memory Protection Unit (MPU) included.
* Memory:
* Up to 256 kB on-chip flash programming memory with 256 Byte page write and erase.
* Up to 36 kB SRAM
* 4 kB EEPROM.
* ROM API support:
* Boot loader with boot options from flash or external source via USART or C_CAN
* ADC drivers
* SPI drivers
* USART drivers
* I²C drivers
* Power profiles and power mode configuration with low-power mode configuration option
* DMA drivers
* C_CAN drivers
* Flash In-Application Programming (IAP) and In-System Programming (ISP).
* Digital peripherals:
* Simple DMA engine with 18 channels and 20 programmable input triggers.
* High-speed GPIO interface with up to 46 General-Purpose I/O (GPIO) pins with configurable pull-up/pull-down resistors, open-drain mode, input inverter, and programmable digital glitch filter.
* GPIO interrupt generation capability with boolean pattern-matching feature on eight external inputs.
* Two GPIO grouped port interrupts.
* Switch matrix for flexible configuration of each I/O pin function.
* CRC engine.
* Quadrature Encoder Interface (QEI).
* Configurable PWM/timer/motor control subsystem:
* Up to four 32-bit counter/timers or up to eight 16-bit counter/timers or combinations of 16-bit and 32-bit timers.
* Up to 28 match outputs and 22 configurable capture inputs with input multiplexer.
* Dither engine for improved average resolution of pulse edges.
* Four State Configurable Timers (SCTimers) for highly flexible, event-driven timing and PWM applications.
* SCT Input Pre-processor Unit (SCTIPU) for processing timer inputs and immediate handling of abort situations
* Integrated with ADC threshold compare interrupts, temperature sensor, and analog comparator outputs for motor control feedback using analog signals.
* Special-application and simple timers:
* 24-bit, four-channel, multi-rate timer (MRT) for repetitive interrupt generation at up to four programmable, fixed rates.
* Repetitive interrupt timer for general purpose use and use with debug time-stamping.
* Windowed Watchdog timer (WWDT).
* High-resolution 32-bit Real-time clock (RTC) with selectable 1 s or 1 ms time resolution running in the always-on power domain. RTC can be used for wake-up from all low power modes including Deep power-down.
* Analog peripherals:
* Two 12-bit ADC with up to 12 input channels per ADC and with multiple internal and external trigger inputs and sample rates of up to 2 Msamples/s. Each ADC supports two independent conversion sequences. ADC conversion clock can be the system clock or an asynchronous clock derived from one of the three PLLs.
* One 12-bit DAC.
* Integrated temperature sensor and band gap internal reference voltage.
* Four comparators with external and internal voltage references (ACMP0 to 3). Comparator outputs are internally connected to the SCTimer/PWMs and ADCs and externally to pins. Each comparator output contains a programmable glitch filter.
* Serial interfaces:
* Three USART interfaces with DMA, RS-485 support, autobaud, and with synchronous mode and 32 kHz mode for wake-up from Deep-sleep and Power-down modes. The USARTs share a fractional baud-rate generator.
* Two SPI controllers.
* One I²C-bus interface supporting fast mode and Fast-mode Plus with data rates of up to 1Mbit/s and with multiple address recognition and monitor mode.
* One C_CAN controller.
* Clock generation:
* 12 MHz internal RC oscillator trimmed to 1 % accuracy for -25 °C ≤ Tamb ≤ +85 °C that can optionally be used as a system clock.
* Crystal oscillator with an operating range of 1 MHz to 25 MHz.
* Watchdog oscillator with a frequency range of 503 kHz.
* 32 kHz low-power RTC oscillator with 32 kHz, 1 kHz, and 1 Hz outputs.
* System PLL allows CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. May be run from the system oscillator or the internal RC oscillator.
* Two additional PLLs for generating the SCTimer/PWM clocks.
* Clock output function with divider that can reflect the crystal oscillator, the main clock, the IRC, or the watchdog oscillator.
* Power control:
* Integrated PMU (Power Management Unit) to minimize power consumption.
* Reduced power modes: Sleep mode, Deep-sleep mode, Power-down mode, and Deep power-down mode.
* APIs provided for optimizing power consumption in active and sleep modes and for configuring Deep-sleep, Power-down, and Deep power-down modes.
* Wake-up from Deep-sleep and Power-down modes on activity on USART, SPI, and I²C peripherals.
* Wake-up from Sleep, Deep-sleep, Power-down, and Deep power-down modes from the RTC alarm or wake-up interrupts.
* Timer-controlled self wake-up from Deep power-down mode using the RTC high-resolution/wake-up 1 kHz timer.
* Power-On Reset (POR).
* BrownOut Detect BOD).
* JTAG boundary scan modes supported.
* Unique device serial number for identification.
* Single power supply 2.4 V to 3.6 V.
* Temperature range -40 °C to +105 °C.
* Available as LQFP64 package.
## Target Applications
* Motor control
* Motion drives
* Digital power supplies
* Solar inverters
* Home appliances
* Building and factory automation
* Industrial and medical
## Features

Show

LPC1519JBD64E Specifications

Attribute	Attribute Value

Datasheet	Datasheet
3D Model	3D Model
Mounting Style	Surface Mount
Number of Pins	64 Pin
Case/Package	LQFP-64
Frequency	72 MHz
Supply Voltage (DC)	2.40V (min)
Number of Positions	64 Position
Clock Speed	72.0 MHz
RAM Memory Size	36 KB
Number of Bits	32 Bit
Power Dissipation	1500 mW
Number of ADCs	2 ADC
Number of Inputs and Outputs	22 Input IO
Operating Temperature (Max)	105 ℃
Operating Temperature (Min)	-40 ℃
Power Dissipation (Max)	1500 mW
Number of DACs	1 DAC
Supply Voltage	2.4V ~ 3.6V
Supply Voltage (Max)	3.6 V
Supply Voltage (Min)	2.4 V
	Show
Operating Temperature	-40℃ ~ 105℃
Product Lifecycle Status	Active
Packaging	Tray
RoHS	RoHS Compliant
Lead-Free Status	Lead Free
REACH SVHC Compliance Edition	2015/12/17

Order guide

Payment Shipping Package Order Quality Assurance

TT in advance (bank transfer), Western Union, Credit card,
PayPal. Customer is responsible for shipping fee, bank
charges, duties and taxes.
- You can choose whether shipping charges will be charged through your shipping account or by us.
- Please confirm with the logistics company in advance for remote areas.
(Additional charges ($35-$50) may apply for delivery in these areas)
- Delivery date: usually 2 to 7 working days.
- A tracking number will be sent after your order ships.
- Carefully inspected and packed by ManyChip warehouse
- Vacuum packaging
- Anti-static packaging
- Shockproof foam
The terms here are for reference only, the actual terms are subject to the sales quotation.
- Please confirm product specifications when ordering.
- MOQ refers to the minimum order quantity required to purchase each part.
- If you have special ordering instructions, please indicate them on the ordering page.
- Inspection (PSI) will be performed prior to shipment.
- Income Quality Control (IQC), 1000+ qualified dealers.
- Chips are tested by authoritative organizations to ensure the quality, authenticity and safety of your device.
- Decapsulation control
- X-ray control
- XRF inspection
- Electrical testing
- Surface testing
-Digital components warehouse, covering an area of 800 square meters, with constant temperature and humidity

Contact Us

If you have any problem,please email to sales@manychip.com, we will response as soon as possisble.

Popular Search Parts

Recommended Parts
Hot Parts
Popular Parts
Recently Popular Parts

SN:H2.1458LO16200V34Q0QC0S0

Buy LPC1519JBD64E

Please fill the information below to send RFQ quickly,and we will respond immediately.